[pkg-wpa-devel] Bug#849077: Bug#849077: wpasupplicant: [Regression] Updating wpasupplicant makes not possible to connect to encrypted WiFi
Scott Mcdermott
scott at smemsh.net
Sat Dec 24 06:45:31 UTC 2016
my machine is having an identical looping scan failure
messages as did the submitter after recent update.
worked: 2.5-2+v2.4-3+b1
broken: 2.6-2
device: 03:00.0 Network controller: Broadcom Limited BCM4360 802.11ac Wireless Network Adapter (rev 03)
driver: Broadcom BCM43a0 802.11 Hybrid Wireless Controller 6.30.223.271 (r587334)
ifupdown: 0.8.16
broadcom-sta-dkms: 6.30.223.271-5
/etc/network/interfaces.d/wlan0-supplicant:
iface wlan0 inet dhcp
wpa-driver nl80211
wpa-conf /etc/wifirc
wpa-debug-level 3
/etc/wifirc:
ap_scan=1
network={
ssid="myssid"
psk="mypassword"
}
...
notes:
- computer is a mbpr 11,1
- rfkill shows as allowed
- tried rebuilding dkms, does not work
- tried reloading wl.ko, does not work
- reboot after downgrade wasn't needed, worked right away
- not using systemd or NetworkManager (not installed)
- no driver backtraces exist in my syslogs
- new wpasupplicant *does* work ok with a usb rtl8187
EOM
(syslog below)
: wpa_supplicant v2.6
: random: Trying to read entropy from /dev/random
: Successfully initialized wpa_supplicant
: Initializing interface 'wlan0' conf '/etc/wifirc' driver 'nl80211' ctrl_interface 'N/A' bridge 'N/A'
: Configuration file '/etc/wifirc' -> '/etc/wifirc'
: Reading configuration file '/etc/wifirc'
: update_config=1
: ap_scan=1
: ctrl_interface='DIR=/var/run/wpa_supplicant'
: Line: 17 - start of a new network block
: priority=5 (0x5)
: PSK (from passphrase) - hexdump(len=32): [REMOVED]
: Priority group 5
: id=0 ssid='myssid'
: nl80211: Supported cipher 00-0f-ac:1
: nl80211: Supported cipher 00-0f-ac:5
: nl80211: Supported cipher 00-0f-ac:2
: nl80211: Supported cipher 00-0f-ac:4
: nl80211: Supported cipher 00-0f-ac:6
: nl80211: interface wlan0 in phy phy0
: nl80211: Set mode ifindex 3 iftype 2 (STATION)
: nl80211: Subscribe to mgmt frames with non-AP handle 0x5573e8060fe0
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=040a
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 04 0a
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=040b
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 04 0b
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=040c
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 04 0c
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=040d
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 04 0d
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=090a
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 09 0a
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=090b
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 09 0b
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=090c
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 09 0c
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=090d
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 09 0d
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=0409506f9a09
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=6): 04 09 50 6f 9a 09
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=7f506f9a09
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=5): 7f 50 6f 9a 09
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=0801
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 08 01
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=06
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=1): 06
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=0a07
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 0a 07
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=0a11
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 0a 11
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=1101
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 11 01
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=1102
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 11 02
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=0505
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 05 05
: nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5573e8060fe0 match=0500
: nl80211: Register frame command failed (type=208): ret=-95 (Operation not supported)
: nl80211: Register frame match - hexdump(len=2): 05 00
: nl80211: Failed to register Action frame processing - ignore for now
: rfkill: initial event: idx=2 type=1 op=0 soft=0 hard=0
: netlink: Operstate: ifindex=3 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
: Add interface wlan0 to a new radio phy0
: nl80211: Regulatory information - country=00
: nl80211: 2402-2472 @ 40 MHz 20 mBm
: nl80211: 2457-2482 @ 20 MHz 20 mBm (no IR)
: nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
: nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
: nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
: nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
: nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
: nl80211: 57240-63720 @ 2160 MHz 0 mBm
: nl80211: Added 802.11b mode based on 802.11g information
: wlan0: Own MAC address: 3c:15:c2:aa:bb:cc
: wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
: wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
: wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
: wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
: wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=4 set_tx=0 seq_len=0 key_len=0
: wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=5 set_tx=0 seq_len=0 key_len=0
: wlan0: RSN: flushing PMKID list in the driver
: nl80211: Flush PMKIDs
: wlan0: Setting scan request: 0.100000 sec
: TDLS: TDLS operation not supported by driver
: TDLS: Driver uses internal link setup
: TDLS: Driver does not support TDLS channel switching
: wlan0: WPS: UUID based on MAC address: 211e8a77-c908-5644-a5b3-e8ec52bbe890
: ENGINE: Loading dynamic engine
: ENGINE: Loading dynamic engine
: EAPOL: SUPP_PAE entering state DISCONNECTED
: EAPOL: Supplicant port status: Unauthorized
: nl80211: Skip set_supp_port(unauthorized) while not associated
: EAPOL: KEY_RX entering state NO_KEY_RECEIVE
: EAPOL: SUPP_BE entering state INITIALIZE
: EAP: EAP entering state DISABLED
: wlan0: Added interface wlan0
: wlan0: State: DISCONNECTED -> DISCONNECTED
: nl80211: Set wlan0 operstate 0->0 (DORMANT)
: netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
: Daemonize..
: random: Got 20/20 bytes from /dev/random
: RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=6 linkmode=0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
: RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=5 linkmode=0 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
: RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=5 linkmode=1 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
: wlan0: State: DISCONNECTED -> SCANNING
: wlan0: Starting AP scan for wildcard SSID
: wlan0: Add radio work 'scan'@0x5573e8083620
: wlan0: First radio work item in the queue - schedule start immediately
: wlan0: Starting radio work 'scan'@0x5573e8083620 after 0.000008 second wait
: wlan0: nl80211: scan request
: nl80211: Scan extra IEs - hexdump(len=6): 7f 04 00 00 0a 02
: nl80211: Scan trigger failed: ret=-22 (Invalid argument)
: wlan0: State: SCANNING -> DISCONNECTED
: nl80211: Set wlan0 operstate 0->0 (DORMANT)
: netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
: wlan0: CTRL-EVENT-SCAN-FAILED ret=-22 retry=1
: wlan0: Radio work 'scan'@0x5573e8083620 done in 0.000088 seconds
: wlan0: radio_work_free('scan'@0x5573e8083620: num_active_works --> 0
: wlan0: Setting scan request: 1.000000 sec
: EAPOL: disable timer tick
: wlan0: State: DISCONNECTED -> SCANNING
: wlan0: Starting AP scan for wildcard SSID
: wlan0: Add radio work 'scan'@0x5573e8083620
: wlan0: First radio work item in the queue - schedule start immediately
: wlan0: Starting radio work 'scan'@0x5573e8083620 after 0.000016 second wait
: wlan0: nl80211: scan request
: nl80211: Scan extra IEs - hexdump(len=6): 7f 04 00 00 0a 02
: nl80211: Scan trigger failed: ret=-22 (Invalid argument)
: wlan0: State: SCANNING -> DISCONNECTED
: nl80211: Set wlan0 operstate 0->0 (DORMANT)
: netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
: wlan0: CTRL-EVENT-SCAN-FAILED ret=-22 retry=1
: wlan0: Radio work 'scan'@0x5573e8083620 done in 0.000089 seconds
: wlan0: radio_work_free('scan'@0x5573e8083620: num_active_works --> 0
: wlan0: Setting scan request: 1.000000 sec
: wlan0: State: DISCONNECTED -> SCANNING
: wlan0: Starting AP scan for wildcard SSID
: wlan0: Add radio work 'scan'@0x5573e8083620
: wlan0: First radio work item in the queue - schedule start immediately
: wlan0: Starting radio work 'scan'@0x5573e8083620 after 0.000024 second wait
: wlan0: nl80211: scan request
: nl80211: Scan extra IEs - hexdump(len=6): 7f 04 00 00 0a 02
: nl80211: Scan trigger failed: ret=-22 (Invalid argument)
: wlan0: State: SCANNING -> DISCONNECTED
: nl80211: Set wlan0 operstate 0->0 (DORMANT)
: netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
: wlan0: CTRL-EVENT-SCAN-FAILED ret=-22 retry=1
: wlan0: Radio work 'scan'@0x5573e8083620 done in 0.000120 seconds
: wlan0: radio_work_free('scan'@0x5573e8083620: num_active_works --> 0
: wlan0: Setting scan request: 1.000000 sec
: wlan0: State: DISCONNECTED -> SCANNING
: wlan0: Starting AP scan for wildcard SSID
: wlan0: Add radio work 'scan'@0x5573e8083620
: wlan0: First radio work item in the queue - schedule start immediately
: wlan0: Starting radio work 'scan'@0x5573e8083620 after 0.000029 second wait
: wlan0: nl80211: scan request
: nl80211: Scan extra IEs - hexdump(len=6): 7f 04 00 00 0a 02
: nl80211: Scan trigger failed: ret=-22 (Invalid argument)
: wlan0: State: SCANNING -> DISCONNECTED
: nl80211: Set wlan0 operstate 0->0 (DORMANT)
: netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
: wlan0: CTRL-EVENT-SCAN-FAILED ret=-22 retry=1
...
More information about the Pkg-wpa-devel
mailing list