[Debburn-devel] Problem that could not be solved

[watari at freenet.de]

Hello, while trying to burn a CD with wodim on my Debian/Etch i encountered an error which prevented burning and for which i could not find a remedy elsewhere. I will attach the standard output and the error output of wodim while i tried to burn. It would be very kind to get an answer that might solve this problem. Thank you for your attention!

Standard output:

TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : 'HL-DT-ST'
Identification : 'DVDRAM GSA-4167B'
Revision       : 'DL12'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x001A (DVD+RW)
Profile: 0x001B (DVD+R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x0010 (DVD-ROM)
Profile: 0x0009 (CD-R) (current)
Profile: 0x000A (CD-RW)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
FIFO size      : 12582912 = 12288 KB
Track 01: data   536 MB
Total size:      616 MB (61:04.16) = 274812 sectors
Lout start:      616 MB (61:06/12) = 274812 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 4
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type A, high Beta category (A+) (3)
  ATIP start of lead in:  -11077 (97:34/23)
  ATIP start of lead out: 359848 (79:59/73)
Disk type:    Long strategy type (Cyanine, AZO or similar)
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 85036
Starting to write CD/DVD at speed  24.0 in real SAO mode for single session.
Last chance to quit, starting real write    0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Writing pregap for track 1 at -150
write track pad data: error after 0 bytes
BFree: 1029 K BSize: 1029 K
Starting new track at sector: 0
Track 01:    0 of  536 MB written.
write track data: error after 0 bytes
Writing  time:    5.064s
Average write speed 730.9x.
Fixating...
Fixating time:    0.004s

Error output:

scsidev: '2,0,0'
scsibus: 2 target: 0 lun: 0
Linux sg driver version: 3.5.34
Wodim version: 1.1.2
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
Errno: 12 (Cannot allocate memory), read buffer scsi sendcmd: no error
CDB:  3C 00 00 00 00 00 00 FC 00 00
status: 0x0 (GOOD STATUS)
cmd finished after 0.000s timeout 200s
Speed set to 4234 KB/s
Errno: 12 (Cannot allocate memory), write_g1 scsi sendcmd: no error
CDB:  2A 00 FF FF FF 6A 00 00 1F 00
status: 0x0 (GOOD STATUS)
cmd finished after 0.000s timeout 200s
Errno: 12 (Cannot allocate memory), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 00 00 00 00 1F 00
status: 0x0 (GOOD STATUS)
cmd finished after 0.000s timeout 200s
/usr/bin/X11/wodim: A write error occured.
/usr/bin/X11/wodim: Please properly read the error message above.